Metrological relations between the spray atomization parameters of a cutting fluid and formation of a surface topography and cutting force
Authors:
- Radosław W. Maruda,
- Natalia Szczotkarz,
- Szymon Wojciechowski,
- Józef Gawlik,
- Grzegorz M. Królczyk
Abstract
Aerosol formation parameters are very important, as they are responsible for the ability of spray-forming droplets to penetrate the area to which they are applied. Research into modifying these parameters can therefore provide a solution for increasing the effectiveness of cooling and lubrication of the cutting zone during machining. This is particularly important for hard-to-cut materials such as titanium alloys, the machining of which requires the selection of effective cooling/lubricating methods to reduce tool wear or improve the machined surface quality. Previous research indicates that any modification in the air or oil flow rates – which form aerosols during cutting in minimized quantity lubrication (MQL) technique – contribute to an increase or decrease in the penetration of droplets into the cutting zone. It can consequently has a significant impact on machining results. This paper presents results on the effect of volumetric air flow rate P and oil mass flow rate E during the MQL cutting method on the machined surface topography after turning of Ti6Al4V alloy. On the basis of conducted computational fluid dynamics (CFD) simulation studies, it was shown that the droplet size is more influenced by the change in volumetric air flow rate than oil mass flow rate and also that as the value of P increases, the droplet diameters decrease and the spray angle increases, which promotes the penetration of the cutting zone. As a result of the analysis of selected 3D surface roughness parameters, as well as contour maps, isometric views and material ratio curves, it was shown that the most favorable machined surface topography is being formed during MQL turning method with a volumetric air flow rate above 20 l/min. Whereby, with conditions of P = 30 l/min and E = 1.182 g/min, the machined surface topography is characterized by a uniform distribution of irregularity peaks and valleys, compared to the MQL turning with other tested values of aerosol formation parameters.
- Record ID
- CUTecfada7e38cf424e9b3c03e8c464cfee
- Publication categories
- ;
- Author
- Journal series
- Measurement, ISSN 0263-2241, e-ISSN 1873-412X
- Issue year
- 2023
- Vol
- 219
- Pages
- [1-20]
- Article number
- 113255
- Other elements of collation
- rys.; schem.; tab.; wykr.; Bibliografia (na s.) - 18-20; Bibliografia (liczba pozycji) - 48; Oznaczenie streszczenia - Abstr.; Numeracja w czasopiśmie - Vol. 219
- Keywords in English
- minimum quantity lubrication (MQL), volumetric air flow rate, cutting fluid mass flow rate, droplet size, surface topography, cutting force
- ASJC Classification
- ; ; ;
- DOI
- DOI:10.1016/j.measurement.2023.113255 Opening in a new tab
- URL
- https://www.sciencedirect.com/science/article/pii/S0263224123008199 Opening in a new tab
- Related project
- Modelowanie zagadnień hydrodynamiki tworzenia medium czynnego z nanocząsteczkami podczas obróbki ubytkowej w warunkach zminimalizowanego chłodzenia i smarowania. . Project leader at PK: , ,
- Language
- eng (en) English
- License
- Score (nominal)
- 200
- Score source
- journalList
- Score
- Publication indicators
- Additional fields
- Indeksowana w: Web of Science, Scopus
- Uniform Resource Identifier
- https://cris.pk.edu.pl/info/article/CUTecfada7e38cf424e9b3c03e8c464cfee/
- URN
urn:pkr-prod:CUTecfada7e38cf424e9b3c03e8c464cfee
* presented citation count is obtained through Internet information analysis, and it is close to the number calculated by the Publish or PerishOpening in a new tab system.